Dry-film thickness, commonly abbreviated DFT, is the thickness of the coating remaining on a surface after the appropriate drying or curing stage. It is often expressed in micrometres. Hiding the substrate's colour does not prove that the required thickness has been achieved. In industrial paint specifications, individual-coat thickness and total-system thickness may be separate requirements. The target, measurement method and acceptance criteria depend on the product, substrate and project. A thicker application is not automatically better, and one reading cannot be assumed to represent an entire coated object.
The difference between wet and dry film
Wet-film thickness describes the applied layer while the coating is still wet. During drying and film formation, volatile components leave the film, so wet and dry thickness are not automatically equal. Volume solids can help describe the relationship under the relevant conditions. A percentage stated by mass cannot simply replace the volume-solids percentage in that calculation. Mixing and thinning conditions also matter. Wet-film checks are useful for controlling application, but they should not automatically be substituted for the specified final dry-film inspection procedure.
A simple volume-solids calculation
In a simplified theoretical relationship, dry-film thickness equals wet-film thickness multiplied by the volume-solids fraction. As an arithmetic illustration only, a material with 50 percent volume solids would give approximately 50 micrometres dry film from 100 micrometres wet film. This is not an application instruction for any Versan product. Use the selected product's actual data at the defined mixing condition. Thinning, surface profile and application conditions can affect interpretation in practice. The calculation supports planning; it does not replace product instructions or the appropriate measurement of the finished coating.
Individual coats and the complete system
Clarify whether a specified value applies to the primer, the finish or the whole system. Where an epoxy primer and epoxy topcoat are used together, the targets for individual layers are not interchangeable with the total target. A final combined reading does not establish that every preceding layer was correctly applied. Inspection of professional coating systems therefore needs records at appropriate stages. Before adding a layer, confirm the condition of the previous coating and its recoating requirements as well as any relevant thickness results.
Selecting a method for the substrate
Do not assume that the same measurement approach is suitable for steel, aluminium, galvanizing, timber and concrete. The physical properties of the coating and substrate affect method selection. ISO 2808 covers methods for determining paint and varnish film thickness. The instrument's intended use, reference checks and measurement conditions must be appropriate. Roughness, edges, curved parts and restricted access can influence interpretation. Record the method and substrate along with the numerical result so that the reading can be understood and reviewed later.
Combined readings over galvanized steel
A paint film on galvanized steel sits over an existing zinc layer. Some magnetic measurements can include both paint and zinc in the reading. Do not report that combined result as paint-only thickness without establishing the measurement basis. For paint systems on galvanized steel, plan the layer distinction and reference approach before inspection. Subtracting unrelated readings taken at different positions is not automatically a valid separation method. The capability of the instrument and the specified acceptance procedure must be considered together.
Sampling and acceptance decisions
An acceptable average can conceal local areas that are too thin or too thick. Define the measurement locations, sample count, treatment of individual readings and acceptance limits before starting. There is no single universal tolerance appropriate to every coating project. A first-sample approval plan can help establish these decisions early. When results are outside the required range, investigate the cause and the suitability of the repair procedure before adding more paint. Thickness inspection does not eliminate the need to consider adhesion, curing, continuity or visible defects.
Theoretical coverage and actual consumption
Theoretical spreading rate can be estimated from volume solids and the target dry-film thickness using consistent units. Such a calculation does not fully represent application losses, geometry or the influence of surface profile. Overspray, material retained in equipment and touch-up work can increase practical consumption. Products sold by mass require the appropriate density information before converting to volume. Compare industrial coatings at equivalent film targets and system scopes. The container price alone is less informative than the practical cost of producing the required coating on the actual area.
Building a traceable inspection record
Record the component or area identity, product and batch, layer sequence, application date, inspection time, instrument or method and reference checks. Measurement positions can be linked to a drawing, photograph or defined zone number. Keep repair and reinspection results in the same record chain. These details make the original system easier to understand during later maintenance. When requesting a technical assessment, provide the substrate, coating sequence and measurement conditions together. An isolated thickness number without that context rarely supports a reliable conclusion about the application.
Check before selecting
| Decision | What to verify |
|---|---|
| Target | Define individual-coat and total-system thickness requirements. |
| Units and data | Use consistent thickness units and the correct volume-solids basis. |
| Method | Choose an approach suitable for the coating and substrate. |
| Reference | Check the instrument and account for profile and existing layers. |
| Acceptance | Agree sampling locations, result interpretation and specification limits. |
| Traceability | Record area, layer sequence, timing, results and corrective actions. |
Turning a system into an application plan
The following framework supports selection and application decisions within this product family. It does not replace numerical product instructions.
Select the auxiliary product as part of the system
A thinner, primer, application tool or supporting layer must be assessed alongside the finish chemistry and substrate. Products sold under the same general description may differ in solvent strength, drying behaviour or intended use. A liquid that cleans equipment is not necessarily suitable for thinning the coating. Consult the specified product and recommended components before treating availability as evidence of technical compatibility.
Use representative trials and controlled application
A small trial on the actual substrate can reveal absorption, flow or existing-coating incompatibility before large-scale work. Prepare it using the intended tool and product proportions. Thinning beyond specified limits can change dry-film formation even where the wet material appears easier to apply. Record cleaning, environmental conditions and overcoating intervals. Do not accept the process solely from the appearance of the freshly applied film.
Maintain safe handling and traceable information
For solvent-containing and aerosol products, follow the safety data sheet for ventilation, ignition control and suitable protection. Waterborne does not mean that every hazard has been eliminated. Keep the product label, batch information and technical documentation in the application record. Manage leftover material, contaminated solvent and pressurised containers according to instructions; do not discharge waste into drains. Confirm storage conditions and shelf life from the actual product documentation.
Information to prepare for a technical enquiry
Before discussing a project, record substrate material, existing coating condition, approximate area and service environment. Photographs help locate defects, but do not independently establish moisture, adhesion or chemical compatibility. Describe indoor or outdoor exposure, cleaning, expected traffic and application access. For production or maintenance, include scheduling constraints, temperature and the planned return to service. Consider primer, ancillary materials and preparation as well as packaging. Do not create a definitive application recipe from a commercial quantity alone. Providing this information in your quotation request helps establish the relevant technical questions early.
Reading documentation and accepting the work
Technical and safety data sheets serve different purposes. Technical data describes application and performance scope; safety data describes chemical hazards, protection and handling precautions. Match the document’s product name, code and date to the actual components. Take numerical mixing, thickness and waiting instructions from the relevant current document. An archive catalogue may help identify a product family, but does not replace current site approval. At completion, retain batches, application conditions, preparation and inspection findings. Agree acceptance criteria in advance and assess the specified system against service needs, rather than judging the work solely by its appearance.
Frequently asked questions
Which unit is normally used for dry-film thickness?
Micrometres are commonly used. If the instrument or specification uses another unit, verify the conversion. A number recorded without its unit is insufficient for acceptance or a meaningful product comparison.
Does complete hiding prove that the thickness is correct?
No. Hiding power and film thickness are different characteristics. A visually covered surface can still fall outside the target range. Use the appropriate method and the defined inspection plan.
Does a thicker coating always provide better protection?
No. Excessive thickness outside the product's recommended range may cause drying or appearance problems. Evaluate both lower and upper requirements in the context of the coating and complete system.
Can wet-film measurement replace dry-film inspection?
Not automatically. Wet-film control helps guide application, while the final film depends on volume solids, mixing conditions and film formation. Perform acceptance inspection according to the specified procedure.
Does every gauge measure paint alone on galvanizing?
No. Some methods can include zinc and paint together. Establish the instrument's capability and reference approach, and state that measurement basis when reporting the result.
Related products and resources
Explore relevant products, categories and application information. Confirm suitability against the product documentation and project conditions.
Technical references
- ISO 2808:2019 — Determination of film thickness
- DeFelsko technical library — Thickness measurement of zinc and paint layers
Content: Versan Boya knowledge library. References support concepts and assessment; another manufacturer's properties are not assigned to Versan products. Archive documents do not replace current application approval. Project-specific decisions require current product documentation and technical assessment.
Let us assess your substrate and requirements.
Add your preferred products and packs to the quote basket. Submit a technical and commercial enquiry without membership or a purchase commitment.